It may seem hard to believe today, but post-war Royal Enfield motorcycles were known for advanced design features.
Swing-arm rear suspension, telescopic forks, cush drive, the neutral finder and spacious tool boxes were appreciated by motorcyclists. I purchased a 2006 Honda motorcycle and was stunned to discover that it had no oil filter, a feature Royal Enfield Bullet riders have enjoyed since 1939.
But one Royal Enfield feature always left me perplexed: the "quick detach" rear wheel. Oh, it's a terrific idea: take off one nut, slide out the axle, and the wheel is off, without affecting the chain or rear brake settings.
It's once you have the wheel off that you realize you can't get it out from under the fender!
Even if the tire is dead flat, there just isn't enough clearance.
The owner's manual of my 1999 Bullet helpfully suggests that you tip the motorcycle over on its centerstand and fish the wheel out from under the fender and muffler. I've done that. It's no fun.
Frustrating, too, is that you can just see the easy solution: if only the fender had a hinge in it, you could swing it up and away for clearance.
Not until I'd owned my Bullet for years did I learn the truth: the Bullet rear fender is hinged!
Plenty of room to remove the wheel.
Loosen one nut on either side of the motorcycle and it swings up and out of the way — assuming you have the solo seat.
Owners of machines with dual seats will have to unbolt and remove the seat; avoiding this is no doubt why the owner's manual suggested the Tip and Tug method.
I learned this trick from David Hill, of Franklin, Mass., who told everyone about it on the Royal Enfield Yahoo Message Group. He even noted that your spark plug wrench is the perfect size to loosen the nuts, just above the rear pegs, that hold the fender in place.
Spark plug wrench fits the nuts perfectly.
This method applies to the time honored Bullet, but what about the new C5 and G5 models? I wrote to Greg Stewart ("Scooter Bob"), technical services expert for Classic Motorworks. He replied:
"The C5 will do just that – but you’ll need to put the G5’s centerstand up on a piece of board and probably tip it to one side to get the wheel assembly out from under the bike. They still have the “quick hub” like ALL good Brit bikes should have – but they moved the drive chain to the right side.''
Swing-arm rear suspension, telescopic forks, cush drive, the neutral finder and spacious tool boxes were appreciated by motorcyclists. I purchased a 2006 Honda motorcycle and was stunned to discover that it had no oil filter, a feature Royal Enfield Bullet riders have enjoyed since 1939.
But one Royal Enfield feature always left me perplexed: the "quick detach" rear wheel. Oh, it's a terrific idea: take off one nut, slide out the axle, and the wheel is off, without affecting the chain or rear brake settings.
It's once you have the wheel off that you realize you can't get it out from under the fender!
Even if the tire is dead flat, there just isn't enough clearance.
The owner's manual of my 1999 Bullet helpfully suggests that you tip the motorcycle over on its centerstand and fish the wheel out from under the fender and muffler. I've done that. It's no fun.
Frustrating, too, is that you can just see the easy solution: if only the fender had a hinge in it, you could swing it up and away for clearance.
Not until I'd owned my Bullet for years did I learn the truth: the Bullet rear fender is hinged!
Plenty of room to remove the wheel.Loosen one nut on either side of the motorcycle and it swings up and out of the way — assuming you have the solo seat.
Owners of machines with dual seats will have to unbolt and remove the seat; avoiding this is no doubt why the owner's manual suggested the Tip and Tug method.
I learned this trick from David Hill, of Franklin, Mass., who told everyone about it on the Royal Enfield Yahoo Message Group. He even noted that your spark plug wrench is the perfect size to loosen the nuts, just above the rear pegs, that hold the fender in place.
Spark plug wrench fits the nuts perfectly.This method applies to the time honored Bullet, but what about the new C5 and G5 models? I wrote to Greg Stewart ("Scooter Bob"), technical services expert for Classic Motorworks. He replied:
"The C5 will do just that – but you’ll need to put the G5’s centerstand up on a piece of board and probably tip it to one side to get the wheel assembly out from under the bike. They still have the “quick hub” like ALL good Brit bikes should have – but they moved the drive chain to the right side.''
